Grundfos 1/6 HP 115V Circulating Pump Cast Iron Body
The Grundfos UP26-120 U is a cast iron circulator pump for closed circulation of water. The Grundfos model utilizes a two-pole, single phase motor at 1/6 (0.16) HP and produces a flow range of 0-19 GPM and a head range of 0-38 ft. The Grundfos UP26-120 U circulator pump functions at 115V, 2.15 Amp, and 60Hz, and has a maximum pressure of 145 PSI. The optimal water temperature for this Grundfos circulator pump model is within the 32-203 F range.
The Grundfos UP26-120 U circulator pump utilizes a 1-1/4 inch union connection.
The AutoFill™ automatic filling valve is a pressure reducing valve with
a compensating seat, an inlet filter, a shut-off valve and a check valve.
It is installed on the water inlet piping in sealed heating systems, and
its main function is to maintain the pressure of the system to a preset
value, automatically filling up with water as required. This valve has been
designed as pre-adjustable, which means it can be adjusted at the required
pressure value before charging the system. After installation, during the
filling or topping-off phase, the water feed will stop automatically when the
set pressure is reached. There are no levers to flip or valve to close. Preassembled with the backflow preventer, it features an atmospheric vent
which is designed to protect drinking water systems from return flow, caused
by back-siphoning or backpressure, of contaminated fluids. The 573 series
has been specifically certified to standards CSA B64.3 and ASSE 1012.
UP 1510 B7/LC The pump is of the canned rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. The pump is characterized by: Ceramic shaft and radial bearings. Carbon axial bearing. Stainless steel rotor can and bearing plate. Corrosion resistant impeller, Composite, PES. Bronze pump housing. The motor is a 1 phase motor. No additional motor protection is required.
90° Elbow of Polypropylene pipe for use with Venting Gas Appliances. Available in 2", 3", and 4" diameter.
PolyPro is a polypropylene vent pipe for use with ANSI Category II and IV gas burning appliances, including tankless and storage water heaters, high-efficiency water heaters, condensing boilers and warm air furnaces. PolyPro is listed by Intertek to the ULC S636 standard in Canada and is rated as a Class IIA, IIB and IIC vent system suitable for exhaust temperatures up to 230°F / 110°C, and a maximum positive pressure of 15 in-w.c.
45° Elbow of Polypropylene pipe for use with Venting Gas Appliances. Available in 2", 3", and 4" diameter.
PolyPro is a polypropylene vent pipe for use with ANSI Category II and IV gas burning appliances, including tankless and storage water heaters, high-efficiency water heaters, condensing boilers and warm air furnaces. PolyPro is listed by Intertek to the ULC S636 standard in Canada and is rated as a Class IIA, IIB and IIC vent system suitable for exhaust temperatures up to 230°F / 110°C, and a maximum positive pressure of 15 in-w.c.
45° Elbow of Polypropylene pipe for use with Venting Gas Appliances. Available in 2", 3", and 4" diameter.
PolyPro is a polypropylene vent pipe for use with ANSI Category II and IV gas burning appliances, including tankless and storage water heaters, high-efficiency water heaters, condensing boilers and warm air furnaces. PolyPro is listed by Intertek to the ULC S636 standard in Canada and is rated as a Class IIA, IIB and IIC vent system suitable for exhaust temperatures up to 230°F / 110°C, and a maximum positive pressure of 15 in-w.c.