Search results for 'flame sensor'

The A419 series controls are single-stage, electronic temperature controls with a Single-Pole, Double-Throw (SPDT) output relay. They feature a lockable front-panel touchpad for setup and adjustment, and a Liquid Crystal Display (LCD) for viewing the temperature and status of other functions. A Light-Emitting Diode (LED) indicates the controls? output relay On/Off status. The A419 controls are available in 24 VAC or 120/240 VAC powered models. The A419 controls have heating and cooling modes, adjustable setpoint and differential, an adjustable anti-short cycle delay, and a temperature offset function. The setpoint range is -30 to 212°F (-34 to 100°C). The controls feature remote sensing capability and interchangeable sensors. The A419 controls are available in either NEMA 1, high-impact plastic enclosure suitable for surface or DIN rail mounting or NEMA 4X watertight, corrosion-resistant surface-mount enclosures.

The A419 series controls are single-stage, electronic temperature controls with a Single-Pole, Double-Throw (SPDT) output relay. They feature a lockable front-panel touchpad for setup and adjustment, and a Liquid Crystal Display (LCD) for viewing the temperature and status of other functions. A Light-Emitting Diode (LED) indicates the controls? output relay On/Off status. The A419 controls are available in 24 VAC or 120/240 VAC powered models. The A419 controls have heating and cooling modes, adjustable setpoint and differential, an adjustable anti-short cycle delay, and a temperature offset function. The setpoint range is -30 to 212°F (-34 to 100°C). The controls feature remote sensing capability and interchangeable sensors. The A419 controls are available in either NEMA 1, high-impact plastic enclosure suitable for surface or DIN rail mounting or NEMA 4X watertight, corrosion-resistant surface-mount enclosures.

The Water Valve Rebuild Kit contains all the parts needed to replace the water control valve assembly.

The water control valve assembly may need to be replaced when:

• Main burner will not turn on
• Main burner is on low flame
• Water is not hot enough, or as hot as usual

IN THE KIT

• Diaphragm
• “O” Ring
• Spindle
• Washers
• Retaining Clip
• Instructions

The microprocessor-based, AZEL Technologies Digital Temperature gauge DS-60 represents the “next generation” in temperature gauge industries. The bold, hi-contrast LCD display ensures accurate temperature reading to the tenth degree and can be easily read from greater distances than the typical mechanical temperature gauge. DS-60 REPLACES TWO mechanical temperature gauges as it can centralize the readings in one spot and simultaneously display the accurate temperatures of supply and return piping on a hydronic heating system. In addition, the solid state temperature sensor probe can be extended up to several hundred feets. The unit is designed to be powered by 24VAC input or by lithium battery. When 24VAC is supplied, the lithium battery enable the unit to work in case of power failure. Its features also include Min/Max memory which shows the highest and lowest temperature after the last reset and instant Fahrenheit to Centigrade conversion. DS-60 is also ideal for any application (EG. Solar heating or Geothermal) that requires quick and accurate response to temperature change, an easy to read display and a wide temperature range.

PTC Silicon Sensor

The Steca TA OP1 overvoltage protection unit is a connection socket in a splash-proof IP65 protective case and serves to protect the collector sensor against local lightning strikes and externally induced voltage spikes.

 A varistor protective diode protects against atmospheric overvoltages that can lead to the destruction of the collector sensor. The use of the Steca TA OP1 is generally recommended for extra protection of the collector sensor in any type of solar thermal system. In addition, the simple operation of the spring terminals allows rapid and simple installation of the collector sensors using a sensor extension cable.

Immersion sensors allow temperature recording in liquid and gaseous media and are designed for installation in existing or on-site immersion sleeves. The standard measurement unit contains a Pt1000 temperature sensor, according to DIN EN 60 751, class B, in a two-core connection.

Product features

■For installation in immersion sleeves

Our STR 1 includes everything that is needed for a thermal solar system. Apart from the controller for temperature differences an electronically controlled limitation of the storing temperature has been built in. Of course, it is possible to adjust hysteresis, temperature difference and max. storing temperature individually. By using the hand-gear control you can adjust the pump for testing or other operations. A display indicating the temperature informs you about the collector temperature to be stored. Another very important point was the breakdown safety switch which does not lower your solar system’s performance since it is very low in self-consumption. The regulator is supplied including a collector temperature sensor and a storage temperature sensor in the lower storage tank area for limiting the maximum storage temperature.

• Individually adjustable switch-on temperature difference, switch-off hysteresis and maximum storing temperature
• Display unit for the storing and collector temperature
• Temperature sensor with error flag
• Storing temperature limitation
• Easiest assembly and handling
• Coordinate safety concept
• Hand-gear control
• Status display

The Steca Suntana solar thermal controller is another member of our solar thermal controller family. The controller monitors and controls solar thermal systems with one collector array, one storage tank and alternatively with an appropriate back-up heating or circulation pump.

Apart from controlling the solar energy system, the controller also performs important system monitoring and safety functions. The system parameters and measured values can be viewed and modified via a 2 x 16-digit LCD display. The amount of solar energy fed from the collector array into the storage tank can be read from the LCD display at any time, thanks to a volumetric flow meter with pulse output. The controller has a maximum of five inputs for temperature measurement, a digital pulse input for recording heat quantity, and two outputs for controlling pumps. A programmable timer with selectable switching times for controlling a solar circuit pump is integrated into the controller. Installation mistakes are avoided from the very beginning through the automatic recognition of the temperature sensors. The components delivered with the controller include one collector temperature sensor and two storage tank sensors.