Tankless Water Heaters | Search results for: 'Other branks of tankless water heaters'

Watts Radiant 1/2" Swedge Manifold Open Ended-2 outlets

Watts Radiant 1/2" Swedge Manifold Open Ended

Swedged Manifolds are Easy to Stock and Easy to Assemble. There is Sufficient Copper on the Closed End to Cut off and Sweat to Another Manifold. Solder a 2-Branch to a 3 Branch to Make a 5 Branch, a 3-Branch and a Four Branch to make a 7 Branch etc. Four Fitting Styles are Available: Onix, PEX Crimp, RadiantPEX-AL Press, and RadiantPEX-AL Compression. Swedged Manifolds are Sold Individually, with or without Mini Ball Valves (MBVs).

$25.90

Watts Radiant 1/2" Swedge Manifold Open Ended-3 outlets

Watts Radiant 1/2" Swedge Manifold Open Ended

Swedged Manifolds are Easy to Stock and Easy to Assemble. There is Sufficient Copper on the Closed End to Cut off and Sweat to Another Manifold. Solder a 2-Branch to a 3 Branch to Make a 5 Branch, a 3-Branch and a Four Branch to make a 7 Branch etc. Four Fitting Styles are Available: Onix, PEX Crimp, RadiantPEX-AL Press, and RadiantPEX-AL Compression. Swedged Manifolds are Sold Individually, with or without Mini Ball Valves (MBVs).

$28.81

Watts Radiant 3/8" Swedged Manifolds Open Ended with Mini Ball Valve

Swedged Manifolds are Easy to Stock and Easy to Assemble. There is Sufficient Copper on the Closed End to Cut off and Sweat to Another Manifold. Solder a 2-Branch to a 3 Branch to Make a 5 Branch, a 3-Branch and a Four Branch to make a 7 Branch etc. Four Fitting Styles are Available: Onix, PEX Crimp, RadiantPEX-AL Press, and RadiantPEX-AL Compression. Swedged Manifolds are Sold Individually, with or without Mini Ball Valves (MBVs).

$52.31

Watts Radiant 3/8" Swedged Manifolds Open Ended with Mini Ball Valve-2 outlets

Watts Radiant 3/8" Swedged Manifolds Open Ended with Mini Ball Valve

Swedged Manifolds are Easy to Stock and Easy to Assemble. There is Sufficient Copper on the Closed End to Cut off and Sweat to Another Manifold. Solder a 2-Branch to a 3 Branch to Make a 5 Branch, a 3-Branch and a Four Branch to make a 7 Branch etc. Four Fitting Styles are Available: Onix, PEX Crimp, RadiantPEX-AL Press, and RadiantPEX-AL Compression. Swedged Manifolds are Sold Individually, with or without Mini Ball Valves (MBVs).

$52.31

Watts Radiant 3/8" Swedged Manifolds Open Ended with Mini Ball Valve-3 outlets

Watts Radiant 3/8" Swedged Manifolds Open Ended with Mini Ball Valve

Swedged Manifolds are Easy to Stock and Easy to Assemble. There is Sufficient Copper on the Closed End to Cut off and Sweat to Another Manifold. Solder a 2-Branch to a 3 Branch to Make a 5 Branch, a 3-Branch and a Four Branch to make a 7 Branch etc. Four Fitting Styles are Available: Onix, PEX Crimp, RadiantPEX-AL Press, and RadiantPEX-AL Compression. Swedged Manifolds are Sold Individually, with or without Mini Ball Valves (MBVs).

$60.06

Watts Radiant 3/8" Swedged Manifolds Open Ended with Mini Ball Valve-4 outlets

Watts Radiant 3/8" Swedged Manifolds Open Ended with Mini Ball Valve

Swedged Manifolds are Easy to Stock and Easy to Assemble. There is Sufficient Copper on the Closed End to Cut off and Sweat to Another Manifold. Solder a 2-Branch to a 3 Branch to Make a 5 Branch, a 3-Branch and a Four Branch to make a 7 Branch etc. Four Fitting Styles are Available: Onix, PEX Crimp, RadiantPEX-AL Press, and RadiantPEX-AL Compression. Swedged Manifolds are Sold Individually, with or without Mini Ball Valves (MBVs).

$86.47

Watts Radiant 1/2" Swedged Manifolds Open Ended with Mini Ball Valve

Swedged Manifolds are Easy to Stock and Easy to Assemble. There is Sufficient Copper on the Closed End to Cut off and Sweat to Another Manifold. Solder a 2-Branch to a 3 Branch to Make a 5 Branch, a 3-Branch and a Four Branch to make a 7 Branch etc. Four Fitting Styles are Available: Onix, PEX Crimp, RadiantPEX-AL Press, and RadiantPEX-AL Compression. Swedged Manifolds are Sold Individually, with or without Mini Ball Valves (MBVs).

$49.40

Watts Radiant 1/2" Swedged Manifolds Open Ended with Mini Ball Valve-2 outlets

Watts Radiant 1/2" Swedged Manifolds Open Ended with Mini Ball Valve

Swedged Manifolds are Easy to Stock and Easy to Assemble. There is Sufficient Copper on the Closed End to Cut off and Sweat to Another Manifold. Solder a 2-Branch to a 3 Branch to Make a 5 Branch, a 3-Branch and a Four Branch to make a 7 Branch etc. Four Fitting Styles are Available: Onix, PEX Crimp, RadiantPEX-AL Press, and RadiantPEX-AL Compression. Swedged Manifolds are Sold Individually, with or without Mini Ball Valves (MBVs).

$49.40

Caleffi 548 Series Hydro Separator with ANSI Flanges-4" ANSI Flanged connection w/Insulation

0

Series 548 Hydro Separator with ANSI Flanges. This device consists of several different functional components, each meet specific requirements, typical of the circuits used in heating and air-conditioning systems. • Hydronic separator: To keep connected hydronic circuits totally independent from each other • Dirt remover: To permit the separation and collection of any impurities present in the circuits. Provided with a valved connection with discharge piping. • Automatic air vent valve: For automatic venting of any air contained in the circuits. Provided with a valved connection for maintenance purposes. The hydronic separator should be sized according to the maximum flow rate value at the inlet. The selected design value must be the greatest between the primary circuit and the secondary circuit. When a single system contains a primary production circuit, with its own pump, and a secondary user circuit, with one or more distribution pumps, operating conditions may arise in the system whereby the pumps interact, creating abnormal variations in circuit flow rates and pressures. The hydronic separator creates a zone with a low pressure loss, which enables the primary and secondary circuits connected to it to be hydraulically independent of each other; the flow in one circuit does not create a flow in the other if the pressure loss in the common section is negligible. In this case, the flow rate in the respective circuits depends exclusively on the flow rate characteristics of the pumps, preventing reciprocal influence caused by connection in series. Therefore, using a device with these characteristics means that the flow in the secondary circuit only circulates when the relevant pump is on, permitting the system to meet the specific load requirements at that time. When the secondary pump is off, there is no circulation in the secondary circuit; the whole flow rate produced by the primary pump is by-passed through the separator. With the hydronic separator, it is thus possible to have a primary production circuit with a constant flow rate and a secondary distribution circuit with a variable flow rate; these operating conditions are typical of modern heating and cooling systems.

Regular Price: $5,000.00

Special Price: $1,836.67

Caleffi 548 Series Hydro Separator with ANSI Flanges-5" ANSI Flanged connection without Insulation ASME

Without Insulation-ASME tagged and registered

Series 548 Hydro Separator with ANSI Flanges. This device consists of several different functional components, each meet specific requirements, typical of the circuits used in heating and air-conditioning systems. • Hydronic separator: To keep connected hydronic circuits totally independent from each other • Dirt remover: To permit the separation and collection of any impurities present in the circuits. Provided with a valved connection with discharge piping. • Automatic air vent valve: For automatic venting of any air contained in the circuits. Provided with a valved connection for maintenance purposes. The hydronic separator should be sized according to the maximum flow rate value at the inlet. The selected design value must be the greatest between the primary circuit and the secondary circuit. When a single system contains a primary production circuit, with its own pump, and a secondary user circuit, with one or more distribution pumps, operating conditions may arise in the system whereby the pumps interact, creating abnormal variations in circuit flow rates and pressures. The hydronic separator creates a zone with a low pressure loss, which enables the primary and secondary circuits connected to it to be hydraulically independent of each other; the flow in one circuit does not create a flow in the other if the pressure loss in the common section is negligible. In this case, the flow rate in the respective circuits depends exclusively on the flow rate characteristics of the pumps, preventing reciprocal influence caused by connection in series. Therefore, using a device with these characteristics means that the flow in the secondary circuit only circulates when the relevant pump is on, permitting the system to meet the specific load requirements at that time. When the secondary pump is off, there is no circulation in the secondary circuit; the whole flow rate produced by the primary pump is by-passed through the separator. With the hydronic separator, it is thus possible to have a primary production circuit with a constant flow rate and a secondary distribution circuit with a variable flow rate; these operating conditions are typical of modern heating and cooling systems.

Regular Price: $8,480.00

Special Price: $3,114.99

Search results for 'Other branks of tankless water heaters'