Search results for 'Ph 32'

Tridicator dual pressure / temperature gage for boilers. Dial size: 3 1/8". Pressure range: 0—75 PSI. Temperature range: 60—320 F. ¼" NPT rear probe.

In heating and air conditioning control systems, the circulation of water containing impurities may result in rapid wear and damage to components such as pumps and control valves. It also causes blockages in heat exchangers, heating elements and pipes, resulting in lower thermal efficiency within the system. The dirt separator separates off these impurities, which are mainly made up of particles of sand and rust, collecting them in a large collection chamber, from which they can be removed even while the system is in operation. This device is capable of efficiently removing the smallest particles, with low head loss.

Wet rotor circulation pump, with flanged connection. (Flange perpendicular to shaft). Cast iron body for hot-water heating systems of all kinds, industrial circulation systems, cold-water systems and air-conditioning systems.

In heating and air conditioning control systems, the circulation of water containing impurities may result in rapid wear and damage to components such as pumps and control valves. It also causes blockages in heat exchangers, heating elements and pipes, resulting in lower thermal efficiency within the system. The dirt separator separates off these impurities, which are mainly made up of particles of sand and rust, collecting them in a large collection chamber, from which they can be removed even while the system is in operation. This device is capable of efficiently removing the smallest particles, with low head loss.

UP 1510 B7/LC The pump is of the canned rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. The pump is characterized by: Ceramic shaft and radial bearings. Carbon axial bearing. Stainless steel rotor can and bearing plate. Corrosion resistant impeller, Composite, PES. Bronze pump housing. The motor is a 1 phase motor. No additional motor protection is required.

Dual check continuous pressure backflow preventer with atmospheric vent. Brass body. Max. working pressure: 175 psi. Working temperature range: 32—210°F. ASSE 1012 listed and CSA B64.3 certified.

Grundfos UPS15-55SFC is a 1/8HP, 3-speed Stainless steel Circulator Pump with removalble Integral Check Valve and flanged connections. 3 speeds of the Grundfos UPS15-55SFC model make this pump very versatile and allow to match the system's requirements by adjusting the speeds (Low/Med/High), thus optimizing it's performance. Stainless steel body of the circulator resists corrosion and allows to use UPS15-55SFC model in a variety of applications ranging from open loop radiant and hot water recirculation, to closed loop hydronic heating and even chilled water cooling. This model also replaces a number of competitive models from Taco, Bell & Gosset, Wilo and others.

The AutoFill™ automatic filling valve is a pressure reducing valve with a compensating seat, an inlet filter, a shut-off valve and a check valve. It is installed on the water inlet piping in sealed heating systems, and its main function is to maintain the pressure of the system to a preset value, automatically filling up with water as required. This valve has been designed as pre-adjustable, which means it can be adjusted at the required pressure value before charging the system. After installation, during the filling or topping-off phase, the water feed will stop automatically when the set pressure is reached. There are no levers to flip or valve to close. Preassembled with the backflow preventer, it features an atmospheric vent which is designed to protect drinking water systems from return flow, caused by back-siphoning or backpressure, of contaminated fluids. The 573 series has been specifically certified to standards CSA B64.3 and ASSE 1012.

Webstone Isolation Flanges with Drain are designed for residential and commercial use with all 2 bolt flanged circulator pumps. The unitary construction of the brass body and flange provide strength and versatility for any application where a pipe and flange meet. This valve is the only choice to use in a closed system where a large port drain and fill valve is required.Additional wing style "T" handle included with mounting nuts and bolts.