Search results for 'gas water heater'

2 Unions, 2 Gaskets

Swedged Manifolds are Easy to Stock and Easy to Assemble. There is Sufficient Copper on the Closed End to Cut off and Sweat to Another Manifold. Solder a 2-Branch to a 3 Branch to Make a 5 Branch, a 3-Branch and a Four Branch to make a 7 Branch etc. Four Fitting Styles are Available: Onix, PEX Crimp, RadiantPEX-AL Press, and RadiantPEX-AL Compression. Swedged Manifolds are Sold Individually, with or without Mini Ball Valves (MBVs).

CENTRAL HEATING CLEANER F3

• Neutral universal cleaner for pre-commissioning new systems in accordance with BS7593:2006

• Removes sludge, limescale and other debris to restore heating efficiency of existing systems

• When used in conjunction with Protector F1 gas savings of up to 15% can be achieved every time you heat your room

• Carbon Footprint certified by the Carbon Trust

• Compatible with all metals and materials commonly used in heating systems

• Easy to use, system can be left running normally during cleaning

• Suitable for use with all known powerflushing machines

• Neutral, non-hazardous formula (COSHH rated zero)

Fernox Cleaner F3 is designed to remove all debris, sludge and scale from existing systems of all ages. In this way, it will restore heating efficiency and eliminate or reduce boiler noise. It has also been designed for pre-commission cleansing new installations inaccordance with BS7593:2006, removing flux residues and other debris, thereby helping extend the life of a system. For older sludged systems, Cleaner F3 is particularly effective when used in conjunction with a powerflushing unit. If the system is heavily scaled the use of Fernox DS40 System Cleaner is recommended. Cleaner F3 is a neutral, non-hazardous product that is well inhibited and compatible with all metals and materials commonly used in heating systems. For continued long term protection the system should be thoroughly cleansed and flushed in accordance with BS7593:2006 and Benchmark using Fernox Cleaner F3, before treating with Fernox Protector F1. We recommend Protector levels are checked regularly (annually).

‘If you clean a central heating system using Fernox F3 Cleaner, and protect with Fernox F1 Protector, you can restore and maintain system efficiency resulting in a gas saving of up to 15% every time you heat your room. This saving is equivalent to 90 Kg CO2e per typical home per year.’ This is the equivalent to saving 2400 hours of operating a standard 60W light bulb, or leaving the same light bulb on continuously for 100 days!

•  
• All operating components located indoors for weather
• Capacities up to 250,000 BTU/hr.
• Accommodates vent pipe runs up to 100 equivalent feet.
• Regulated, consistent draft throughout burner cycle.
• Built-in Fan Proving Switch interlocks with gas valve.
• Available with 24-volt Relay or Post Purge Timer/Relay.
• Kit includes everything needed for installation, except vent pipe. (*GPAK* includes DC-4 Draft Control)
• Durable, heavy-duty aluminum Vent Hood.
• AGA design certified for gas furnaces, boilers, pool
• heaters, unit heaters and commercial water heaters.
• 
   

 

In heating and air conditioning control systems, the circulation of water containing impurities may result in rapid wear and damage to components such as pumps and control valves. It also causes blockages in heat exchangers, heating elements and pipes, resulting in lower thermal efficiency within the system. The dirt separator separates off these impurities, which are mainly made up of particles of sand and rust, collecting them in a large collection chamber, from which they can be removed even while the system is in operation. This device is capable of efficiently removing the smallest particles, with low head loss.

Grundfos UP15-29SU model circulator incorporates a stainless steel body design and 1-1/4" union connection, smaking it suitable for a wide range of open and closed loop radiant heating, hydronic heating, hot water recirculation, solar & other applications.

Wet rotor circulation pump, with union connection. Bronze body for domestic hot water applications

Viessmann Vitoden Gas Boilers

 100-W Gas Fired Wall-Mounted Condensing Boiler with Modulating Stainless Steel Cylinder Burner and Inox-Radial Heat Exchanger Service.

 

Model		WB1B 26	WB1B 35
CSA input	MBH kW	37 - 91 8.5 - 23.4	37 - 118 8.5 - 29.3
CSA output *	MBH kW	34 - 83 7.6 - 21	34 - 108 7.6 - 26.4
Efficiency (A.F.U.E.)	%	95.2	95.2
Altitude levels	ft. m	0 - 10,000 0 - 3,048	0 - 10,000 0 - 3,048
Overall dimensions
Depth	inches mm	14⅛ 360	14⅛ 360
Width	inches mm	15¾ 400	15¾ 400
Height	inches mm	28½ 725	28½ 725
Shipping weight	lbs kg	95 43	95 43

* Output based on 140ºF / 60ºC, 120ºF / 49ºC system supply/return temperature.

Viessmann CombiPLUS Kit for Vitodens 100-WB1B

Optional On Demand Domestic Hot Water Kit for Reliable DHW Without a Tank.

 

Heats a 2 ½ car garage. Turns unheated space into a workshop, exercise room or laundry room.